Used Equipment Warranty

 

 

Used Equipment Warranty
Limited Warranty
Used equipment, sold by Screen printing Products Inc. is warranted against defects in
Parts and materials for a period of sixty (60) days commencing the date received . Any
part found by Screen printing Products Inc. to be defective material or workmanship
within the stated warranty period will be replaced or repaired without charge for parts
Only persons specifically authorized by Screen Printing Products Inc. shall perform
warranty work on the equipment. Any work performed by unauthorized persons shall
void this warranty. Consequential damages, lost productive hours, inconvenience and
contingent liabilities are not covered under this warranty.
All service technician travel, lodging, time, and sustenance costs remain solely the
Buyer’s responsibility. Screen printing Products Inc. sole liability under this warranty
shall be to replace or repair defects in materials and parts.
Screen Printing Products Inc. does not warrant failure of parts or components resulting
from misuse, improper adjustment, lack of proper maintenance, electrical current
surges, or from general wear. Damage to the Equipment while being crated or
transported by a third party provider or due to damage caused by installation by other
than a qualified manufacturer’s technician are specifically excluded from this warranty.
Also excluded from this Warranty Agreement are damages caused by natural disasters,
such as earthquakes, hurricanes, floods, tornados and fires.
The Equipment subject to this Warranty Agreement is used and Screen Printing
Products Inc. is not a manufacturer or distributor of this Equipment. Other than
the warranty described above .

Sprint Gas Dryers - What to Expect

Sprint Gas Dryers - What to Expect

-->

Sprint 2000 Gas Dryers - buying used - what to expect

Keep in mind our goal on selling these dryers is to save you up to 50% off the cost of new.

1. Condensation - there will be some discoloration on the outside of the dryer - very typical .
Generally - the older the dryer the more discoloration. There's also always seems to be some rust inside the dryer - this is due to unprotected metal - no need for concern.
2. Insulation - these dryer are well insulated - however during the course of years of use sometimes this insulation needs to be replaced - A very simple process. Basically it's a product called duct board insulation. This is not covered under warranty - but we can buy it at a reduced cost & and we'll carry that cost to you the buyer.  Usual costs if you replace all the insulation is around $400.00 plus shipping.
3. Dryer are always dirty inside - we will always vacuum them out.  We also will wipe down the outside of the dryer as best we can.
4. Hi temp red gasket material (1" wide x 1/8 thick) - this always has to be replaced - Screen Printing Products Inc. will always replace this material - we always leave the old gasket material in place ( always brittle) so as the show where the new should be placed - very simple process.
Scrap off the old - & peel and stick on the new - always clean the surface before placing the new.
5. Belt condition - we'll give it a 1 -10 point rating system - 10 being in excellent condition -
If the belt needs to be replaced we will offer a new belt at our cost. We deal directly with the manufacturers so we can carry on the distributor pricing. (Unless a new belt is negotiated in the deal.)
Things we check and warranty. (60 days parts only)
1. All bearing connected with all fans - this always seems to be a concern- we will replace the bearings parts only - unless you have a certified tech install the dryer - then it's up for discussion- We always pre-determine the conditions of the bearings and report it to the buyer
2. All working parts which make these dryer operational are covered under warranty


Electric Dryers - falls in the same category as gas dryer
Things that are not an issue compared to gas
Bearings / insulation / Red gasket material is not needed

Things that could be an issue:
IR panels/ contactors

Atkins Temp. Probe Screen Print Kit -

 Atkins Temp. Probe

Most accurate way to measure Ink Temperature 
(in new condition)

direct spec sheet link: http://www.cooper-atkins.com/Products/Thermocouples/AquaTuff_35200_K_Screen_Print_Kit_93916-K/

AquaTuff 35200-K Screen Print Kit

Model #: 93916-K

The 93916-K Screen Print Kit with AquaTuff™ 35200-K Waterproof Thermocouple Instrument and 50008-K Screen Print Donut Probe, allows you to monitor precise ink temperatures when profiling dryers to ensure perfect prints every time!

Used Equipment Recent Article

             Used Equipment Article
                         In Wearable Magazine

This is a recent article coming out of Wearable Magazine - Good press for some of us who   sell Used Screen Printing Equipment the right way - Just proud of the way we do business

New Conveyor Belts

HIGH TEMPERATURE TEFLON COATED DRYER BELTS
FOR GAS, ELECTRIC or UV DRYERS

· AVAILABLE IN TAN or BLACK COLORS

· UPGRADE YOUR EQUIPMENT WITH A NEW BELT

 How to measure your belt :

double click to enlarge

for pricing contact us 415-895-1507 ask for Dave

Equipment Form

double click to enlarge

When you submit a piece of equipment to be sold on our site we need
to have this form filled out -

Also how to prep pictures of your equipment:

1.     Clean the control panel (10 Min.) – take a picture

2.     Clean 1 print Head really good (20 Min.) – take a picture

3.     Then back off & take a picture of the whole machine

 If your using a Iphone make sure you send the pictures “actual size”

The phone will ask you that before it sends

 email back to either:

Dave - norris.mac@gmail.com

or

Brian - spproducts22@gmail.com